Enerdrive 100AH B-TEC W/ DC2DC Charger 40 plus
Enerdrive B-TEC LiFeP04 12v 100Ah Slimline Lithium Battery
Available in 12v 100Ah, 125Ah, 200Ah and 300Ah capacities and 24v 150Ah & 36v 100Ah, the ePOWER B-TEC lithium battery is designed and intended for use in deep cycle applications where a single battery is required that meets the amp hour capacity.
Smart Phone Monitoring System
The Enerdrive Enerdrive B-TEC Slimline battery incorporates wireless Battery Monitoring Technology. By downloading the Android™ or Apple® app to your smartphone or tablet device, you can monitor the following information;
- Battery Capacity
- Battery Voltage
- Battery Current (Amps)
- Battery State of Charge (SOC)
- Battery State of Health (SOH)
- Battery Status
- Individual Cell Voltage
- Battery Temperature
- Battery Cycles
- Battery Alarms
- Battery Event Information
Battery Management System
The battery is also equipped with an internal Battery Management System that can monitor and optimise each Prismatic cell within the battery during normal operation. It will protect the battery pack from over charge, over discharge, over temperature & short circuit. The BMS helps to ensure safe and accurate operation of the battery.
Size & Weight Savings
Lithium v AGM Capacities;
- 100Ah Lithium = 160Ah AGM
- 125Ah Lithium = 200Ah AGM
- 200Ah Lithium = 320Ah AGM
- 300Ah Lithium = 480Ah AGM
(Based on standard depth of discharge for both Lithium (80%) and AGM (50%).
The Enerdrive B-TEC battery provides 60% more usable power than its equivalent lead acid cousin and being nearly 50% lighter and 30% smaller makes for a superior alternative.
The Enerdrive B-TEC Slimline battery is perfect for camper trailers, 4WD’s (AUX battery), caravans, small water craft, low power communication sites or any other application that requires the use of a single deep cycle battery that meets the amp hour capacity.
With over 7 years of researching, designing and testing lithium batteries and the associated charging systems, Enerdrive are at the forefront of lithium battery systems in Australia. Enerdrive are the only Australian company that can supply a fully integrated self-branded energy system to suit your setup.
With over 3000 complete systems in operation Australia wide, Enerdrive is regarded as the leader in the field of lithium batteries and energy systems for Mobile, Marine and Remote applications.
Please Note; The B-TEC Slimline battery is capable to be paralleled to a second B-TEC battery of the same size. For maximum performance and lifespan of your B-TEC Slimline battery, no more than 2 batteries should be connected together to increase your overall capacity. Overall loads when paralleled should not exceed the current limits of a single batteries BMS.
The 100Ah Slimline battery is able to accept a maximum inverter capacity of 1000W only. Exceeding the maximum inverter capacity can damage the BMS Management within the battery.
If you are requiring a battery system larger than Enerdrive B-TEC battery, please look at the Enerdrive Pro Series Power Pack Systems which can offer multiple parallel and series connections with Active Cell Balancing Protection across the entire pack.
|Cycle Life (DOD – 80% under controlled conditions)||≥ 2000 Cycles|
|Standard Charge Specification (Lithium profile charger required)|
|Battery Charge Temperature||0 ̴ 45°C|
|Normal Charge Voltage CV/CC*||14.20 ̴ 14.60V|
|Standby (Float) Voltage||13.50 ̴ 13.80V|
|Maximum Charge Current||80A @ 25°C for 30mins|
|Recommended Charge Current for Maximum Life||20A-50A|
|Standard Discharge Specification|
|Battery Discharge Temperature||-20 ̴ 60°C|
|Battery Output Voltage Range||11.00 ̴ 14.60V|
|Maximum Discharge Current||100A@25°C ± 5°C for 30mins|
|Pulse Discharge Current||250A for 1.0s|
|Discharge Cut-off Voltage||≤11.20V|
|Circuit Protection||The battery is supplied with a LiFePO4 Battery Management System BMS that can monitor and optimize each single prismatic cell during charge & discharge, to protect the battery pack from overcharge, over discharge & short circuit. Overall, the BMS helps to ensure safe and accurate operation of the battery.|
|Over-charge Protection Per Cell||3.90V ± 0.03V|
|Over-charge Release Per Cell||3.60V ± 0.05V|
|Over-charge Release Method||Discharge below release voltage|
|Over-discharge Protection Per Cell||2.80V ± 0.05V|
|Over-discharge Release Per Cell||3.20V ± 0.05V|
|Over-discharge Release Method||Apply Charge/Voltage ≥12.8V|
|Over Current Protection|
|Discharge Over Current||110A for 30s – 250A for 3s|
|Protection Reset Time||5s Auto Release|
|Over Current Release Method||Disconnect Load|
|Over Temperature Protection|
|Battery Discharge Over Temperature||Protection to 65°C ± 5°C|
|Release at 50°C ± 5°C|
|Battery Charge Over Temperature||Protection to 55°C ± 5°C|
|Release at 45°C ± 5°C|
|Short Circuit Protection||Auto release after 5s|
|Weight||Approx 12.5 Kg|
|Temperature & Humidity Range||≤ 30 days -20°C ̴ 60°C, 5 ̴ 75% RH|
|≥ 30 days -10°C ̴ 45°C, 5 ̴ 75% RH|
|Self-discharge Rate||≤ 3% Per Month|
The Enerdrive 40amp DC2DC Battery Charger with combined Solar Regulator is designed to accept multiple voltage inputs allowing you to charge your batteries through your vehicles alternator or your caravans solar panels. This means you can take advantage of the vehicles alternator whilst moving and your solar panels while you are stationary. The unit will automatically detect and select the best available input source for you. Most other DC2DC chargers do not have this capability and a separate solar controller is needed.
EXPERT TIP: The Enerdrive 60Amp & 70Amp breakers are common accessories suitable for the Enerdrive EN3DC40+ 40A DC to DC charger. Additionally, the 3 pre-wired & fused charging cables are also a great extra accessories, see manuals & drawings for further information. All the accessories are available in the Accessory List above as optional extras.
DC2DC Battery Charger 40A /12V
- Multiple charging inputs allow you accept voltage from your engine and solar panels and convert to 1 output to your battery bank.
- Large battery cable connections - DC M6 screw terminals
- Includes inbuilt (MPPT) solar regulator
- Ability to charge Lithium, Lead Crystal, GEL, AGM, Wet Cell and also create custom profiles.
- Accepts 12 or 24v from your vehicle and a maximum solar input of 45V/800W
- Thermo controlled fan cooling allows 40A output up to 40+°C
- Fully programmable LCD display to show which source is charging the battery along with charger status, voltage and amperage
- Temperature sensor included in charger for more accurate battery charging
During normal operation the ePOWER DC2DC+ Battery Charger will do a full charge cycle to float stage on the house battery bank with ability to choose either GEL, AGM, Flooded, Custom Programmable or Lithium. Once float stage is reached the charger transitions to a power supply mode to support any on-board DC loads.
Multistage Charging Process
The ePOWER DC2DC+ Battery Charger is a fully automatic, set and forget charger. It is designed to quickly and accurately recharge your deep cycle batteries utilising charger algorithms that help to maximise the life of your specialised deep cycle batteries.
The ePOWER DC2DC+ Battery Charger features multistage smart charging technology that enables the charger to be connected to your battery bank permanently. With the input of multiple sources, you can be assured of charging your batteries whenever underway; or when the sun is shining on your solar array.
As dictated by battery manufacturer’s recommendations, deep cycle batteries require a multistage charge sequence for perfect, fast and accurate charging. The Enerdrive ePOWER DC2DC+ smart charger delivers three primary charge stages.
Stage 1 – Bulk or Boost charge; The battery is charged at full rated output current of the charger until the battery reaches its final charging voltage, known as its absorption voltage. In this step, around 80% of the battery is recovered as fast as possible.
Stage 2 – Absorption Charge; With the charger voltage held steady, the remaining 20% is replaced with the charger allowing the current to taper off as the battery approaches full charge.
Stage 3 – Float; Finally, in the float stage the charger voltage is lowered and held at a constant and safe predetermined level. This prevents the battery from being overcharged, yet allows the charger to supply enough current to make up for the self-discharge losses of the battery, while supporting any additional loads connected to the battery (such as DC lighting and refrigerators). This stage allows for the charger to be used as a DC power supply.
Smart Charging Feature
The ePOWER DC2DC+ Battery Charger will regulate its output based on the loads connected to your battery bank. This function is important to maintain the life of your battery bank as some battery chargers mistake loads for discharge and continue to keep the batteries in the bulk or absorption stage for extended periods of time, which will damage the battery bank. The ePOWER DC2DC+ Battery Charger has two methods of load based regulation to ensure your battery charger transitions to float when it should do so.
Battery Temperature Sensor
Included standard with all ePOWER Battery Chargers.
- Model: EN3DC40+
- Output Current: 40A
- Charger Mode Output Voltage: 13.8V - 15.5V
- Float: 13.0V - 13.8V
- Equalize: 15V
- Charging Control: 3 Stages
- DC Output: Single
- Battery Compatablity: Gel, AGM, Flooded, Program
- Charger Efficiency: 95%
- Temperature Setting: Low/Normal/High (Battery Temperature Standard)
- Dimensions: 242mm(L) x 172mm(W) x 74(H)mm
- Weight: 1.9Kg
- Warranty: 2 Years